How can we help?

Lightspeed’s Help Centre is here to provide support, tips and troubleshooting

Intelligent Printing - Setup & Configure

If you’re reading this, you’re looking to set-up Intelligent printing, because your Kounta site is using one or more Windows, Mac, or Albert devices at the POS.

The Epson TMi Intelligent Printer will allow you to immediately print receipts, pop your cash drawer, and print from secondary printers.

Pro Tip - If you’re not sure whether this is the setup you need, then our Kounta App Printing vs. Intelligent Printinguide is worth a read.

By the end of this guide, you’ll know how to set up a fully functional Intelligent Printing System.

 


What's in this guide

Choosing an intelligent printer

Choosing the secondary printer/s

Setting up my intelligent printer system

Step A: Make sure you have everything you need for this setup

Step B: Get the printers ready - do these steps for all printers

Step C: Get the IP addresses of each printer

Step D: Configure the IP addresses of your secondary (non-intelligent) printers

Step E: Configure the IP addresses of your intelligent printer

Step F: Connect the intelligent printer to the secondary printers

Step G: Connect your printers to Kounta

Step H: Connect your printers to the register (receipt printing & cash drawer) 

Step I: Test print & confirm it's all working

Frequently Asked Questions 

 


 

Choosing an intelligent printer

We have a guide that goes through all of our Compatible Printers here.

 


 

Choosing the secondary printer/s

 

Secondary printers can either be intelligent or non-intelligent printers and communicate with the lead intelligent printer via your router.

 

Any of the Ethernet printers in the guide above will be suitable. 

 


 

Setting up my intelligent printer system

Make sure you have everything you need for this setup

             You would need:

 

 

Get the printers ready - do these steps for all printers

1. Load them with paper. The paper should feed from under the roll

2. Connect these cables:

    • Power cable (& turned on)
    • Network/ ethernet cable (the other end should be plugged into the router/data point)
Pro Tip - When working, this port should always have a solid green light. If you do not have a solid green light please check the cable goes to your router, and follow our DHCP guide
    • Cash drawer cable - for any printers with which you plan to use a cash drawer

Ports_Printer.PNG

 

 

Get the IP addresses of each printer

The IP addresses are assigned by the router and, they are the unique identifier for each device on a network so they can all talk to each other.

An example of an IP address is 192.168.0.0 or 10.0.0.0

 

1. New intelligent printers, once turned on, should print an IP address automatically.

2. If you don’t get the IP address automatically, grab a pen and hold in the status button at the back of the printer for three to four seconds - BUT no more than 5 seconds.

WARNING: Holding the pen in for more than five seconds will factory reset the printer. If this happens you will need to read our guide on Enabling DHCP for your printer

LS_Status_sheet_button_status_sheet_intelligent_printer.PNG

3. If any of your printers printed this IP Address: 192.168.192.168 or if your DHCP says disabled, please go to the enabling DHCP guide first.

 

 

Configure the IP addresses of your secondary (non-intelligent) printers

 

1. Please note: these will be done for all secondary printers.

2. Open a browser on your device. (This device should be connected to the same network as the printers.)

3. On the address bar, type in the IP address from one of your non-intelligent printers.

rep_1_intelligent_printer.PNG

 

4. You will be taken to this page. Tap on TCP/IP under Configuration

5. You will see this menu. Change Get IP Address from Auto to Manualrep_2_intelligent_printer.PNG

6. In the same menu, change the last three digits of the IP Address to 201 (for the first), 202 (for the second), 203 (for the third), and so on.

7. In the same menu, select Submit

8. Select Reset

9. Repeat these steps for all non-intelligent printers.

 

 

Configure the IP addresses of your intelligent printer

1. This is for your main intelligent printer.

2. Open a browser on your device. (This device needs to be connected to the same network as the printers.)

3. On the address bar, type in the IP address from one of your intelligent printer. To this address, add “/PrinterConfigurationPage”

  • e.g. 192.168.1.200/PrinterConfigurationPage

IP_address_Intelligent_Printer_Epson_Password.PNG

4. If you are asked to log in - the login details are

  • Username: “ epson ”
  • Password: “ epson ”

 

5. You will be taken to this configuration page. Go to System Settings 

rep_3_intelligent_printer.PNG

6. Then go to TCP/IP under the Wired heading

rep_4_intelligent_printer.PNG

Note - If you open TCP/IP under Wired which is under System Settings BUT cannot edit the fields, it means you have gone to the wrong page - as labelled in the image above 

8. You will see this menu. Change Get IP Address from Auto to Manual

rep_5_intelligent_printer.PNG

 

9. In the same menu, change the last three digits of the IP Address to 200 (i.e 192.168.1.200)

 

10. Select Apply

This will prompt the Printer to restart and apply these changes - will take approximately one minute to complete this process.

 

Connect the intelligent printer to the secondary printers

1. Reconnect to the intelligent printer using your new IP address

  • e.g. 192.168.1.200/PrinterConfigurationPage

 

2. If you are asked for a password and username again, they’re both still “ epson 

3. Go to Printer under the Device Admin heading

rep_6_intelligent_printer.PNG

4. Under Device ID, choose a name for the non-intelligent printer you want to register (e.g. Kitchen). Mind the capitalization. And use underscores for spaces (e.g. Kitchen_pastry)

rep_7_intelligent_printer.PNG

 

5. Select the model of the non-intelligent printer to be registered (ie TM-T82 or TM-T20)

6. Enter the new IP address (ending in 201, 202, 203, and so on) of the non-intelligent printer that you set up in Step D

7. Select Add

8. The printer is added!

9. Repeat steps 4 - 8 for each of your secondary printers

10. One by one, select Test Print for each of your printers to confirm that the details you have entered are correct.

rep_8_intelligent_printer.PNG

 

 

Connect your printers to Lightspeed Kounta

1. Log into Kounta.

2. Head over to Production Printer Settings page in Back Office by selecting Sites then Printers (see image below)

Note - You won't be able to access this page from an Albert device, you would need to do so from a desktop of a mobile device.

3. Update each of the Production Printer Settings fields with the below;

Production Printing Method: Intelligent Print Server

Production printing Font Size: Normal

Intelligent Printer IP Address: <Enter the IP address of your intelligent printer here>

Production Printing: You can choose either All items to all printers or Printer/Item specific - the latter will allow you to print receipts and dockets to specific printers.

 1_Production_Printer_Settings.PNG

4. Select Save 

5. Under Network Printers in this Site, select Add Printer

6. Add the first printer (intelligent printer) under the name local_printer

7. Select Add PrinterScreen_Shot_2018-07-12_at_11.44.51.png

8. Repeat steps 5-7 for all your secondary printers - making sure to use the printer names (capitalisation included) that you assigned in Step F

Heads Up - This is where we can assign items to specific printers and manage our production printing settings

  

 

Connect your printers to the register (receipt printing & cash drawer)

1. Still from Back Office, select Devices under Sites. Then, select Registers 

2. Select the first register you want to configure. 

mceclip0.png

3. Select Printers (see image below)

4. Add the intelligent printer IP address (ending in 200) and select the printers that will print receipts.

5. Repeat steps 2-4 for all registers within the site.

 

3_register_printer_settings.PNG

 

 

Test print & confirm it's all working

1. Now we can go to the POS and confirm everything is working correctly

2. From the Menu on the top left, Select Printing

4_POS_Printing_settings.PNG

 

3. Confirm that the IP address matches and that all the printers you added are here

4. Select Test for each of your printers.

In the same page, you can assign which printer will print receipts, open the cash drawer, and print production dockets.

Test_Print_Kounta.PNG

 

5. The first test will automatically fail because Google Chrome will block it. If this happens, look for the shield icon in the address bar.

6. Select Load Unsafe Scripts

Load_Unsafe_Scripts_Test_Print.PNG

 

7. Select Test again for your printers and, these should now print a test docket from each printer.

 

Pro Tip - Due to settings in Google Chrome, this setting will reset each time your browser is closed so you will need to re-authorise Unsafe scripts for your printing each time your browser is opened.

 


 

What's my next step?

If you haven't already, you might want to set up your printers for production printing.

 


 

Frequently Asked Questions

 

My IP address is 192.168.192.168; what do I do?

This is a sign that your DHCP is disabled.

In some printers, the status sheet printout would say that the DHCP is disabled.

If you encounter any of these, please go to the enabling DHCP guide first.

 

What is the best layout for my hardware?

Are you currently completing your hardware system? We’re here to help.

We have hardware layouts that we recommend for different stores. You can also check out what hardware (apart from printers) work well with your Kounta system. 

  


 

Browse more topics

Was this article helpful?
6 out of 10 found this helpful